Lindy SATA-150 Bedienungsanleitung PDF herunterladen

- 1 -

RAID Native SATA-150 4Ports PCI Host

This Manual for the Models of 4 Channels SATA RAID HBA:

Model A: Serial ATA RAID Internal 4 Ports

Model B: SATA RAID External 2 Port + Internal 2 Port

1. Introduction

This RAID Native SATA-150 4Ports PCI Host Adapter is a PCI to 4Ports Serial

ATA host controller board. It provides a 32bit, 33/66 MHz PCI interface on the

host side and dual, fully compliant Serial ATA ports on the device side to access

SATA Hard disk drive.

The board can be used to upgrade your desktop computer to have 4Ports

Serial ATA Channels and support RAID 0, RAID 1 and RAID 0+1 features. It

accepts host commands through the PCI bus, processes them and transfers

data between the host and Serial ATA devices. The board should be connected

to SATA target device and will take the data, serialize it and output it for

transmission over the SATA interface. The board can control four independent

Serial ATA channels. Each channel has its own Serial ATA bus and will

support one Serial ATA device.

The board supports Serial ATA Generation 1 transfer rate of 1.5 Gb/s (150

MB/s). It comes completely with drivers for Windows 98, Windows Millennium,

Windows NT 4.0, Windows 2000 and XP.

RAID, Redundant Array of Independent Disks, greatly enhances two main

areas of data storage: performance and data integrity. By using RAID 0, also

known as Striping, performance of sustained data transfer rates is greatly

enhanced by simultaneously writing data to 2, 3 or 4 drives. The second

benefit of RAID is data redundancy. RAID 1, Mirroring, writes identical data on

two drives or sets of drives, thus protecting the data from a disk failure. If, for any

reason, one drive were to fail, your data is secure and available from the

1 2 3 4 5 6 7 8 9 10

Inhaltsverzeichnis

Seite 1 - 1. Introduction

- 1 - RAID Native SATA-150 4Ports PCI Host This Manual for the Models of 4 Channels SATA RAID HBA: Model A: Serial ATA RAID Internal 4 Ports Model

Seite 2 - 1.1. Features

- 10 - up, click Yes. And when the Hardware Installation warning pops up, click Yes again. Add Windows XP Driver on Original Booting Device 1. Af

Seite 3 - 2. What Is RAID

- 2 - mirrored second drive. 1.1. Features 1.1.1. PCI Interface !Compliant with PCI Specification, revision 2.2. !Integrated PCI DMA engines. !3

Seite 4 - - 4

- 3 - !Special Shell SATA connectors on External Port to support Mobile HDD, Mobile CD-ROM, Mobile DVD and Mobile CD-RW !One USB-like Connector on

Seite 5 - 4. Software Installation

- 4 - one virtual disk as Striping would do, a second, Mirrored virtual disk is created as well. 3. BIOS Installation ( RAID Setting ) Creating a

Seite 6 - - 6

- 5 - 1. As the BIOS boots, press CTRL+S or F4 to enter the raid bios utility. 2. Select Create RAID set. Press F2. 3. Select Mirrored-Striped set

Seite 7 - - 7

- 6 - This section provides the information on how to install the drivers of RAID Native SATA-150 4Ports PCI Host Adapter for the operating systems

Seite 8 - - 8

- 7 - 4.2. Windows ME Driver Installation For New Windows ME Systems (Fresh Installation) 1. After the SATA RAID PCI Host Adapter and attached driv

Seite 9 - - 9

- 8 - restart your system. 4.3. Windows NT 4.0 Driver Installation For New Windows NT 4.0 System (Fresh Installation) 1. Before installation, copy

Seite 10 - - 10

- 9 - Sil3114\ Win98_me _2000_xp_nt4.0\driver\ *.* to a blank floppy disk. 2. After the SATA RAID PCI Host Adapter and attached drives are configu

Kommentare zu diesen Handbüchern

Keine Kommentare

Lindy SATA-150 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Schnittstellenkarten / Adapter Lindy SATA-150 herunter. Lindy SATA-150 User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Schnittstellenkarten / Adapter Lindy SATA-150